Phico D0 94v0 Lcd Display Datasheet Pdf [2021] -
This article serves as a complete, in-depth resource. We will dissect every part of that keyword—explaining what "PHICO" means, decoding the mysterious "D0", understanding the critical "94V-0" flammability rating, and finally, guiding you on how to find, read, and utilize the elusive datasheet PDF.
| Parameter | Typical Value for PHICO D0 Series | | :--- | :--- | | | 16 Characters x 2 Lines (16x2) | | Display Type | STN (Super Twisted Nematic) or FSTN | | Polarizer Mode | Transflective (readable in sun & via backlight) | | Viewing Direction | 6 o'clock (or 12 o'clock – check datasheet) | | Backlight | Yellow-Green or White LED (parallel or series) | | Controller | KS0066 or S6A0069 (HD44780 compatible) | | Interface | 4-bit or 8-bit parallel (14+2 pins) | | Operating Voltage | 4.5V to 5.5V (typically 5.0V) | | Logic Supply Current | 1.0 mA (typical without backlight) | | Backlight Current | 120-200 mA (depends on color) | | Duty Cycle | 1/16 duty, 1/5 bias | | Operating Temp | 0°C to +50°C (Standard) / -20°C to +70°C (Extended, if specified) | Part 3: The Essential Pinout (Without the Datasheet) Most PHICO 94V-0 displays use the standard 16-pin header configuration (0.1-inch pitch). Here is the pinout you will likely find in the datasheet PDF: phico d0 94v0 lcd display datasheet pdf
| Command | Hex Code | Description | | :--- | :--- | :--- | | Clear Display | 0x01 | Clears screen, returns cursor to home | | Return Home | 0x02 | Returns cursor to home (DDRAM address 0) | | Entry Mode Set | 0x06 | Increment cursor, no shift | | Display ON/OFF | 0x0C | Display ON, Cursor OFF, Blink OFF | | Display ON (with cursor) | 0x0E | Display ON, Cursor ON (underscore) | | Function Set (8-bit) | 0x38 | 8-bit, 2 lines, 5x8 dots | | Function Set (4-bit) | 0x28 | 4-bit, 2 lines, 5x8 dots | | Set DDRAM Address | 0x80 + addr | Set cursor to position (e.g., 0x80 = line 1, col 0) | This article serves as a complete, in-depth resource
Introduction In the world of embedded systems, consumer electronics, and industrial control panels, few components are as ubiquitous yet as technically nuanced as the alphanumeric LCD display. For engineers and hobbyists searching for the term "phico d0 94v0 lcd display datasheet pdf" , you are likely holding a 16x2 or 20x4 character LCD, trying to reverse-engineer a product, or seeking a reliable replacement. Here is the pinout you will likely find
| Pin No. | Symbol | Level | Function | | :---: | :---: | :---: | :--- | | 1 | VSS | 0V | Ground | | 2 | VDD | +5V | Logic Power Supply | | 3 | V0 / VEE | Variable | Contrast Adjustment (via potentiometer to VSS) | | 4 | RS | H/L | Register Select: 0=Command, 1=Data | | 5 | R/W | H/L | Read/Write: 0=Write, 1=Read (often tied to GND) | | 6 | E | H→L | Enable signal (falling edge triggered) | | 7 | DB0 | H/L | Data Bus Bit 0 (LSB) – not used in 4-bit mode | | 8 | DB1 | H/L | Data Bus Bit 1 | | 9 | DB2 | H/L | Data Bus Bit 2 | | 10 | DB3 | H/L | Data Bus Bit 3 | | 11 | DB4 | H/L | Data Bus Bit 4 (MSB of low nibble in 4-bit mode) | | 12 | DB5 | H/L | Data Bus Bit 5 | | 13 | DB6 | H/L | Data Bus Bit 6 | | 14 | DB7 | H/L | Data Bus Bit 7 / Busy Flag | | 15 | LED_A | +5V | Backlight Anode (Power for backlight) | | 16 | LED_K | GND | Backlight Cathode (Ground for backlight) |